Foxwell GT65 ECU Coding OBD Scanner Bidirectional Diagnostic SRS TPMS SAS ABS

Description

Store category
Sign Up Now !
You may also like
Foxwell GT65 ECU Coding OBD Scanner Bidirectional Diagnostic SRS TPMS SAS ABS
Product Description
2021 Global FOXWELL GT65 Bidirectional Scan Tool
All System Diagnosis + 27 Reset Service + Active Test + ECU Coding + Bidirectional + Remote Diagnosis-
ALL Systems' Diagnoses :
To diagnose car comprehensively, FOXWELL GT65 can read DTCs and data streams for ALL systems. For instance: Engines/Auto Transmission/Airbags/Immobilizer/Key Coding/ABS/Cruise Control/Instruments/ Self Leveling Suspension systems/Seats/Doors/Gateway/
Steering Angle/Air Suspension/Body Systems/Electronic Power Steering & Motor Assisted/Power Steering/Tyre Pressure/Rain Sensors/4WD System/Stabilizer/Intelligent Parking Assist/Door Motors/Audio Systems/Air Conditioning/Tiptronic/Anti Theft/Soft Top/Headlamp Leveling/
Central Locking/Automatic Clutch/ DPF Reset/Electric Windows/Plip Programming/Heated Rear Window/Xenon Headlights/Wash Wipe/
Fuel Burning Heater/Transfer Box/Seat Memory/Oil Life Service Reset/Sliding Doors/Electronic Throttle/Navigation System/Rollover Sensor/
Cruise Control/ Multi Function Steering Wheel/Aux Heating/Electronic Parking Brake/Clutch Electronics, ....etc.
(
OVER 100,000 CAR REPAIR
)
ECU Coding:
ECU Coding function is used to re-flash the vehicle control modules, it allows you to recode adaptive data for certain components after making
repairs or replacements, providing ways for the issues of Driveability, Fuel Efficiency, Power Loss, Fault Codes, Durability of Mechanical Parts
Active Test:
Active Tests, also known as Actuator Tests, are bi-directional diagnostic tests on vehicle systems and component. The tests let you to use the scanner temporarily activate or control a vehicle system or component, and when you exit the test, the system/component returns to normal operation. Some tests display a command to the operator. For example, if ?Press Brake Pedal? displays, the operator has to press and hold the brake pedal and then continue. The sequence, number and type of tests are dictated by the control module. On some systems, the actuator tests cannot be restarted until the ignition key is switched off for some time. Alternatively, briefly start and run the engine, shut down, turn the ignition to the run position, then re-initiate the actuator tests.
The tests activate a component, but they do not check if the component is working correctly. Make sure the components to be tested are in good condition and correctly mounted.
A bi-directional:
A bi-directional scan tool is a unique diagnostic tool that can both send and receive information.
With bidirectional control, these devices can send information to and receive information from a vehicles control module.
With these advanced tools, you can perform functional tests, actuator tests, inspection tests, system tests or work with reinitialization and reprogramming.
Wide Vehicle Coverage :
150 car brands and over 10,000 car models.
27 Mechanics Frequently USED Service Functions:
Engine/ABS/SRS/Transmission reset ; Oil Lamp Reset ; TPMS Reset ;Key Programming ;Electronic Parking Brake Reset ;Steering Angle Calibration ;Battery Register / Battery Maintenance ;ABS Bleeding ;Electronic Throttle Position Reset / Learn ;Diesel Particulate Filter (DPF) Regeneration ;Gear Learning ;Injector Coding: ;AFS Reset ;EGR Adaptation ;GEARBOX Reset ; SUNROOF, SUS Reset......
1 -Oil Reset:
The lightening of the car maintenance light indicates that the vehicle needs maintenance.Reset themileage or driving time to zero after the maintenance, so the maintenance light will go out and the systemwill start a new maintenance cycle.
2 -Elec.Throttle Adaption Elec. :
Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learningvalue of the ECU returns to the initial state.By doing these, the movement of the throttle (or idle motor)can be more accurately controlled, thus adjust the intake volume.
3 -Steering Angle Reset :
To reset the steering angle, first find the relative zero point position for the car to drive in straight line.Taking this position as reference, the ECU can calculate the accurate angle for left and right steering.After replacing the steering angle position sensor, replacing steering mechanical parts (such as steeringgearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recoveringcar body, you must reset the steering angle.
4 -Battery Matching :
This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, inwhich the original low battery fault information will be cleared and battery matching will be done.
5 -ABS Bleeding :
When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system torestore ABS brake sensitivity. lf the ABS computer,ABS pump, brake master cylinder, brake cylinder, brakeline, or brake fluid is replaced, the ABS bleeding function must be performed to bleed the ABS.
6 -Break-pad Reset :
lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to theon-board computer to replace the brake pad.After replacing the brake pad, you must reset the brake pad.Otherwise, the car alarms.
7 -DPF Regeneration :
DPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuouscombustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reducePM ignition combustion) to stabilize the filter performance.
8 -Gear Learning :
The crankshaft position sensor learns crankshaft gear machining tolerance and saves to the computerto more accurately diagnose engine misfires. lf gear learning is not performed for a car equipped withDelphi engine, the MlL turns on after the engine is started.The diagnostic device detects the DTC P1336'gear not learned'. In this case, you must use the diagnostic device to perform gear learning for the car.After gear learning is successful, the MIL turns off. After the engine ECU, crankshaft position sensor, orcrankshaft flywheel is replaced, or the DTC 'gear not learned" is present, gear learning must be performed.
9 -IMMO Service :
To prevent the car being used by unauthorized keys, the anti-theft key matching function must beperformed so that the immobilizer control system on the car identifies and authorizes remote control keysto normally use the car. When the ignition switch key, ignition switch, combined instrument panel,ECu,BCM, or remote control battery is replaced, anti-theft key matching must be performed.
10- Injector Coding :
Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder soas to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced,injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identifyinjectors to accurately control fuel injection.
11- TPMS Reset:
After the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting functionmust be performed to reset tire pressure and turn off the tire pressure MIL.Tire pressure resetting mustbe performed after maintenance is performed in the following cases: tire pressure is too low, tire leaks, tirepressure monitoring device is replaced or installed, tire is replaced, tire pressure sensor is damaged,andtire is replaced for the car with tire pressure monitoring function.
12- Suspension Matching :
This function can adjust the height of the body. When replacing the body height sensor in the airsuspension system, or control module or when the vehicle level is incorrect, you need to perform thisfunction to adjust the body height sensor for level calibration.
13- AFS Reset :
This feature is used to initialize the adaptive headlamp system.According to the ambient light intensity, theadaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjustthe headlamp lighting angle while monitoring the vehicle speed and body posture.
14- A/T Learning :
This function can complete the gearbox self-learning to improve gear shifting quality. When the gearbox isdisassembled or repaired (after some of the car battery is powered off), it will lead to shift delay or impactproblem. In this case, this function needs to be done so that the gearbox can automatically compensateaccording to the driving conditions so as to achieve more comfortable and better shift quality.
15- Sunroof Initialization:
This function can set the sunroof lock off, closed when it rains,sliding / tilting sunroof memory function,temperature threshold outside the car etc.
16- EGR Adaption :
This function is used to learn the EGR (Exhaust Gas Recirculation) valve after it is cleaned or replaced.
17 -ODO Reset :
a) ODo reset is to copy,write, or rewrite the value of kilometers in the chip of odometer by using a car diagnostic computer and data cable, so that the odometer shows the actual mileage. b)Usually when the mileage is not correct due to the damaged vehicle speed sensor or odometer failure, it is necessary to do ODo reset after maintenance.
18- Airbag Reset :
This function resets the airbag data to clear the airbag collision fault indicator. When the vehicle collidesand the airbag deploys, the corresponding fault code of the collision data appears, the airbag indicatorlights up, and the fault code cannot be cleared. Since the data inside the airbag computer is disposable,it is required that all new accessories must be replaced, but after performing this function, the data of theairbag computer can be recovered and the fault code can be cleared, the airbag light will go out, and theairbag computer can continue to use.
19- Transport Mode :
ln order to reduce power consumption, the following functions may be disabled,including limiting thevehicle speed, not waking up the door opening network, and disabling the remote control key, etc. At thistime, the transport mode needs to be deactivated to restore the vehicle to normal.
20- A/F Reset :
This function is applied to set or learn Air/Fuel ratio parameters.
ANY MORE......
Wide Vehicle Compatibility
American car models
:
Ford,Lincoin,GM,Buick,Cadillac,Chevrolet,Chrysler,Dodge,Jeep,HM;
European car models
:
Benz,Smart,Sprinter,BMW,VW,SKODA,AUDI,Opel,Lamborghini,PORSCHE,Maybach,Euro Ford,LANDROVER,DR,Bentley,Rolls-Royce,
ROVER,MINI,VAUXHALL,FERRARI,FIAT,Abarth,LANCIA,AlfaRomeo,Maserati,BUGATTI,PEUGEOT,CITROEN,RENAULT,SAAB,VOLVO,OPEL,Dacia,SEAT.
Russian car models
:GAZ, VAZ ;Brazil car models: FIAT; GM
Asian car models
: SAMSUNG,DAEWOO,SSANYYONG,HYUNDAI,KIA,HONDA,Acura,TOYOTA,SCION,LEXUS,MAZDA,NISSAN,Infiniti,JPISUZU,
TLISUZU,
DAIHATSU,SUZUKI,MITSUBISHI,SUBARU,etc.
Malaysia car models
:PERODUA(PERODUA),PROTON
Iran car models
: IKCO,MVM
India car models
: TATA,MARUTI,MAHINDRA;
Australian brand
: AUSFORD, AUS-HOLDEN.
Fast Diagnostic Tool--FOXWELL GT65
Auto VIN Scan –
The GT65 diagnostic system features the latest VIN-Based Auto VIN Scan function to identify vehicles and scan all the diagnosable ECUs and run diagnostics on the selected system. This function is compatible with 2006 and newer vehicles.
ECU Information –
retrieves and displays the specific information for the tested control unit, including unit type, version numbers and other specifications.
Read Codes –
displays detailed information of DTC records retrieved from the test vehicle’s ECU. On some vehicles, freeze frame data can also be retrieved for viewing.
Erase Codes –
erases DTC records and other data from the test vehicle’s ECU.
Live Data –
retrieves and displays live data and parameters from the test vehicle’s ECU.Display live data in text, graph & analog for easy data review.
What You Get:
Payment
Delivery details
Terms of sales
About us
Contact us
Payment
We accept payment via Paypal
.
Payment must be made within 8 days.
Otherwise it will affect your buyer’s credit
If you accidentally placed the wrong order, please contact me to cancel the order
Delivery details
Shipping methods
:
USPS First Class Mail Service /USPS Priority Mail Service
/UPS Surepost
SERVICE
/ UPS GROUND SERVICE
I will process your order within one
business
day (excluding
holiday and weekend
)
If you have any problems, you can contact me first or local USPS, UPS
Terms of sales
Please do not hesitate to leave us your
Positive
Feedback
and
good review
If you are satisfied with our products
I
f you
are unsatisfied
with your purchase,
please
email us first
to get a better solution
before
you leave
a
neutral
or
negative
feedback
,
we work hard to make sure every customer 100% satisfied and resolve any problem for you. Thank you
for your kindness.
About us
We are a professional Authorized dealers of
AUTEL
,
LAUNCH
,
A
NC
E
L
,
F
O
XWELL
,
OBDSTAR，
A
U
T
O
PHI
X
,
KZYEE
,
NEXAS,
Autek ，WOYO，
etc.
We support remote assistance by TeamViewer if you have any difficulty in software installation.
Contact us
Any questions, you can feel free to contact me by ebay message or whatsapp.Due to time difference, I may not be able to reply immediately, but I will reply within 24 hours
Please contact me first before giving negative feedback or opening case. Wish we can solve the problem peacefully.
Working hours:
0:00 am - 3:00 am Pacific Time
， 6:00-9:00 pm Pacific Time, 11:00 pm - 12:00 pm
Pacific Time
.
Feedback
2021 Global FOXWELL GT65 Bidirectional Scan Tool All System Diagnosis + 24+ Reset Service + Active Test + ECU Coding + Bidirectional + Remote Diagnosis-